General Airbrush Operation & Cleaning Guide
[HOW-TO-Use-&-Clean]

View PDFProducts Featured
General Airbrush Operation & Cleaning Guide

This guide is adapted from Sparmax's instructions included with their dual-action, internal-mix airbrushes. We have added useful notes, such as the important message about nozzles below.

IMPORTANT: Never remove the nozzle unless it is already damaged. If you thoroughly clean the airbrush using the procedure in these instructions, it will prevent the nozzle becoming clogged so that you will not need to remove it. Although made from durable, high-quality materials, this part is small and finely engineered. Accidental damage caused by cross-threading, over-tightening, dropping the airbrush, forcing the needle or tools into the nozzle and normal wear are not covered under the warranty. Replacement parts and a repair service are available.

If a damaged nozzle needs to be replaced we advise using specialist tools for the procedure and not the basic spanner provided with the airbrush. Sparmax nozzle tools and the Iwata Nozzle Wrench are designed for this purpose and ensure you get the right angle and torque without risk of over tightening.

Safety Precautions

It is recommended that you work in a well-ventilated area and wear a particle/vapour respirator mask in accordance with the advice of the paint manufacturer. Protect your work area from overspray.

Air pressure

The ideal air pressure will depend on the viscosity (thickness) of the paint, so the best advice is to try varying your working pressure until you settle on your personal preference for each specific brand and colour. Please see your compressor instructions for setting your working pressure.

Pic 1

Paint preparation

Whatever type of paint you use, make sure it is a milky consistency. You may have to mix paint with the appropriate thinner or reducer to achieve this. Always seek instructions from the paint manufacturer on what to use as a thinner. We recommend you use products that are specifically formulated as airbrush colours.

Operating your airbrush (pic 1)

These instructions are for internal mix, double action airbrushes.

Whether you are using a broad or fine spray pattern, if the paint appears wet on the surface then you are using too much paint. This may make the surface tacky and appear shiny, even when it has dried. To avoid this, build up the colour gradually in thin layers which are almost dry as they meet the surface. This also allows you to achieve an even coverage and avoids patchiness. Controlling the amount of colour to achieve broad coverage and fine lines comes with experience – so practise, practise, practise!

Note for pistol trigger airbrushes: Pulling back on the trigger starts the air. Pulling further back controls the amount of fluid being sprayed.

Pic 2

Dagger’ stroke and clean lines (pic 2)

To go from a broad line down to a fine line in one continuous stroke, move the airbrush closer to the surface of your subject and ease the trigger forward while moving the airbrush in a line or arc. This is called a ‘dagger’ stroke because the line comes to a fine point. It is the basis of all artistic freehand airbrushing.

If you see a circular blob (or ‘barbell’) at the beginning and end of the lines, it is because the airbrush was stationary when you started or stopped spraying. Once the air is on, you need to move smoothly towards where you want the line to start, then pull the button back as you come into line with your target (pic 2). Continue moving beyond the end of the line as you release the colour, then stop the air flow. It is good practice to keep the air on ready to start the next stroke if you are going to continue immediately.

Dagger strokes are also achievable with a pistol trigger airbrush using the technique above. For continuous strokes keep the air flowing by not fully releasing the trigger.

Cleaning your airbrush

Keeping your airbrush clean is essential. The vast majority of airbrush problems occur because the airbrush is simply blocked, or has seized up through lack of regular, thorough cleaning. You need to clean your airbrush between every colour change, as well as giving it an extra-thorough clean at the end of the session. For a thorough clean, first flush the airbrush with water to remove the worst of the colour. Follow with a proper airbrush cleaning fluid, then do a final flush with water. Do not allow the paint to sit in the airbrush for longer than necessary.

Pic 3

Flushing procedure (pic 3)

  1. Loosen the needle-chucking nut and pull the needle back a little.
  2. Pour the cleaning fluid into the airbrush cup.
  3. Use a short-bristled, soft brush, such as a stencil brush, to remove any paint inside the cup.
  4. Spray cleaning fluid through the airbrush away from your work and into a cleaning pot or cloth to catch the overspray.
  5. As you spray with more cleaner, cover the needle cap with a soft cloth. This forces air back through the passageways and into the bowl to dislodge any residue. You will see air bubbles in the cup. This is called the ‘backflush’ technique. Do not use a bare finger; avoid risk of forcing compressed air into your bloodstream.
  6. Repeat the flushing procedure until the cleaning fluid runs clear. Spray onto a white cloth or paper towel to test if it is completely clear. If you have been using white colour, it is better to test it against a dark surface.

For siphon/bottom feed airbrushes use the same technique as above using separate bottles for the water and cleaning fluid.

Cleaning needles and needle caps

Once you have thoroughly flushed out the airbrush, you will need to clean the needle and needle cap following the steps below.

Pic 4

  1. Remove the handle and loosen the needle-chucking nut. Dampen a soft cloth with airbrush cleaning fluid.
  2. Remove the needle carefully and draw the needle gently across the cloth whilst rotating it, then repeat. (pic 4)
  3. Unscrew the needle cap and clean the inside with a brush. Clean the nozzle cap if paint has built up on it, but do not remove the nozzle. Replace the needle cap.
  4. Ensure the button is sitting correctly before carefully re-inserting the needle. Use slight pressure to push the needle up into the nozzle until it stops. It helps to rotate the needle a little to ensure it sits properly in position.
  5. Tighten the needle-chucking nut firmly with your fingers

Pic 5

Troubleshooting

  • Air is coming out of the airbrush but no paint.
    • Make sure the needle-chucking nut is tightly gripping the needle so that the trigger is drawing the needle backwards. Clean the airbrush thoroughly.
  • Air is bubbling back into the cup.
    • Make sure the needle cap and nozzle cap are finger-tight. Clean the airbrush thoroughly.
  • Paint is coming out when I press the button for air.
    • Loosen the needle-chucking nut, then reposition the needle in the nozzle, rotating it slightly to ensure it sits properly in position. Tighten the needle-chucking nut.
  • The button/air-valve is sticking.
    • Place a drop or two of non-silicone airbrush lubricant behind the trigger and press the button repeatedly to work it in. To prevent the air valve sticking again, use one drop of lubricant every few sessions.
  • Other problems.
    • If you encounter any other problems, clean your airbrush thoroughly. If the problem still occurs, call the service centre for more troubleshooting advice. Make sure you have the airbrush and compressor with you when you call. The telephone support technician will determine whether you need to send your airbrush into the service centre for diagnosis and repair.

Links to products featured in General Airbrush Operation & Cleaning Guide
Iwata Nozzle Wrench Iwata Nozzle Wrench
Sparmax Dual-headed Airvalve/Nozzle Tool Sparmax Dual-headed Airvalve/Nozzle Tool
Force™8 Half Face Mask with Typhoon Valve and A1P2 Filters (Twin Respirator) Force™8 Half Face Mask with Typhoon Valve and A1P2 Filters (Twin Respirator)
Medea Airbrush Cleaner 4oz (118ml) Medea Airbrush Cleaner 4oz (118ml)
Premi Air Foaming Airbrush Cleaner (150ml) Aerosol Premi Air Foaming Airbrush Cleaner (150ml) Aerosol
Cleaning Brush Cleaning Brush
Sparmax Spray Out Cleaning Pot with Airbrush Hanger Sparmax Spray Out Cleaning Pot with Airbrush Hanger
5-piece Airbrush Cleaning Brush Set 5-piece Airbrush Cleaning Brush Set
Iwata LED Magnifier Iwata LED Magnifier
Iwata Lube (10ml) Iwata Lube (10ml)
Shopping List of all products featured

The Team / 75 Year History
About The Airbrush Company
Contact Us
Find Us
About Us
Become a Retailer
Service
Repairs
Sale / Offers
Search
All major credit and debit cards accepted through Worldpay.
Iwata Professional Airbrushes Products
Brands
Applications
Courses
Shipping
Returns
Terms
Security
PayPal
The Airbrush Company Ltd is the UK distributor of Iwata airbrushes and compressors, Medea, Zazzo, Artool, LifeColor, HR Hobbies and Premi-Air products. We also sell Createx, Wicked, Darkstar, Paasche and Badger. Airbrush Guides:
Choosing Your Airbrush
Iwata Airbrushes
Features Comparison
Airbrush Application Guide
Buyer Beware Guide
How-To Guides
Compressor Guides:
Choosing Air Source
Iwata Studio Series
Compressor Features
Compressor Applications
Airbrush Compatibility
ABC Kit Builder
Shopping Cart
Kit Cart
Checkout
My Account
Privacy
Log In
Log Out
Follow Us
Follow us on Facebook and Twitter
Copyright © 2015 The Airbrush Company Limited
Company No. 2714140. Registered Office:
79 Marlborough Road (East), Lancing Business Park,
Lancing, West Sussex BN15 8UF
Tel. +44 (0)1903 767 800   email: sales@airbrushes.com
Our Airbrush Christmas Cards in support of
Airbrush Charity Christmas Cards in aid of Cancer Research UK