|Tel: +44 (0)1903 767 800|
The section below tells you ways to find the right compressor on our website and the glossary of terms should help. Choosing the wrong machine could prove to be costly. so if in doubt please contact us.
Using cans of propellant may be a way of trying out airbrushing without the outlay of a compressor if you are a beginner or are on a tight budget, but you will not get the best results with propellant and the money you spend replacing the aerosols would be best put towards a compressor.
Finding the right compressor on Airbrushes.com
Our most popular range of compressors are the Iwata Studio Series. We have a complete range to run any of the airbrushes we stock and similar airbrushes. There are no less than 7 ways of looking for a compatible compressor on Airbrushes.com! This is to make it easier - not harder. Just choose the easiest way in for you:
|Click here to view our Compressor Application Guide, Airbrush/Compressor Compatibility Guide and Compressor Comparison Chart.|
|Click here to view our airbrush & compressor kits for all applications!|
|Please call us for advice.|
Air source - a compressor or canned propellant that provides compressed air.
Airflow / Air Volume Delivery - The amount of air that the compressor can deliver. This governs how many airbrushes you can run with the machine. Airflow is measured in CFM (Cubic Feet per Minute) of lpm (litres per minute). You can lookup the volume delivered by our compressors in the Compressor Comparison Chart or on the compressor product pages, whilst the Compressor/Airbrush Compatibility Guide tells you typically how many airbrushes may be run on each model of compressor.
|An Iwata 'Handle-Tank' compressor has an air reservoir built into its tubular handle!|
Air tank / reservoir - A storage tank that the compressor pumps air into, typically found on higher spec machines. This results in a smoother, more controllable airflow. Although an air tank evens out air flow, there is no 'pulsing' of air on any of the Iwata Studio Series compressors that do not have an air tank. The air tank will trap more condensation than a filter alone, so compressors with tanks deliver cleaner, drier air. Also an air storage tank means the compressor motor will not turn on and off as often, so this results in less noise and longer life of the motor and the auto-stop switch.
Automatic / 'Auto-stop' switch - Usually present on compressors with a tank, but also on some without tanks. Iwata call their auto-stop switches 'Smart Technology'. This auto-stop switches the motor off when a maximum pressure in reached, and back on again when the pressure drops to a minimum pressure. These machines can be left on and will begin to run again only when required. This means less motor wear and less noise. These are good solution for longer periods of usage or a busy professional environment.
|An an end-of-line filter traps the last drops of moisture that condense as air cools in the hose.|
Moisture filter - Removes water condensate from the air supply. Condensation coming through your airbrush with the medium can cause spattering or a streaky application. You need to press the moisture release on the filter regularly to avoid excessive build-up of trapped condensation. Also the filters act as a small reservoir on the tank-less models of Iwata compressors, which evens out the airflow so there is no pulsing.
Air becomes hot when compressed. As the air leaves the machine, it decompresses and cools, and any moisture in the air condenses into liquid form. This is more of a problem in colder, humid climates such as the UK, where a moisture filter is essential for all but the smallest compressors. If you have a small compressor with no built-in moisture filter, or even if your compressor does have a moisture filter, you can add an end-of-line moisture filter at the airbrush end of the hose as a last line of defence to trap the last few drops that condense in the air hose as the compressed air cools on its way to the airbrush.
|Iwata Power Jet Pro has twin regulators - one for each outlet.|
Air regulator - Allows adjustment of the air pressure supplied to the airbrush. Usually the compressor also has a pressure gauge so you can see the air pressure and the adjustments you are making and always be able to find your recommended or preferred pressure settings again. A proper compressor regulator gives better control over the air pressure than a simple adjustable air bleed, although even finer control for tiny adjustments in air can be achieved at the airbrush end by adding an external Micro Air Control (MAC) valve or by choosing an airbrush with a built-in MAC Valve, which positions the control right at your fingertips while working.
Air Bleed - Found on machines without an auto-stop. On some machines an air bleed off is crucial to the correct running of the machine, such as tank-less diaphragm machines. In some cases the air bleed is adjustable providing an inexpensive way of pressure adjustment, though not as precise as an air regulator. If you are using pressure to achieve different atomisation effects with the airbrush, then it will be better to use a proper regulator for pressure adjustment.
|Click here to compare the pressure of compressors - or any other tech spec. It may be easier to use the airbrush compatibility guide or application guide on the same page if tech spec is not your thing.|
You will need to ensure the compressor you buy can provide the air pressures required by the application. The Compressor Comparison Chart shows the range of psi (as do the compressor product pages), whilst you may find it simpler to view the Compressor Application Compatibility Guide to see which compressors provide enough air for which applications. It is worth noting that the technical specifications of compressors often quote the maximum standing pressure when no air is being drawn. As soon you press the airbrush or spray gun trigger, some air pressure is let out and so the pressure gauge will always drop a little. The actual 'operating' pressure is therefore lower than the 'standing' pressure. Also the operating pressure achievable will be different depending on the model of airbrush and the air volume it lets through. The quicker the air is taken by the airbrush, the less pressure can be built up by the compressor. Some low to medium quality brands tend to be 'gustier' on air, requiring more air volume and therefore larger, more powerful and noisier compressors. While higher quality airbrushes such as Iwata need less volume of air and can atomise using lower at lower pressures. You can see which compressors can run which airbrushes in our Compressor/Airbrush Compatibility Guide.
Bar - A measurement of air pressure. 1 bar is the atmospheric pressure of the Earth at sea level. 1 bar is approximately 15 psi.
Diaphragm Compressor - A pulsating membrane compresses the air. Diaphragm compressors are fairly noisy and cannot be run for extended periods of time, so they are more suitable for hobby applications than professional use. We recommend attaching a moisture filter to remove condensation from the air supply and to even out the pulsing. We discontinued our last remaining diaphragm compressor a few years ago due to drop-off in demand caused by the huge rise in popularity of our much quieter-running oil-less piston compressors.
Piston Compressor - A piston or pair of pistons compress the air. Piston machines are quiet running and therefore exceptionally well suited to applications where noise would interfere with the creative process or the working environment, such as art studio or beauty salon. A single-piston compressor has one piston and a twin-piston machine has two pistons. A twin piston compressor is approximately twice as powerful as a single-piston compressor because it is compressing twice as much air at the same time, but the extra mechanical work does mean the twin-piston machines are slightly noisier. Also a piston machine running at twice the motor speed or rpm (revolutions per minute) is compressing more air in the time, so it is more powerful, but again noisier - more decibels in noise with a higher pitched sound which is a little more intrusive to the environment. However, whether twin-piston or twice the rpm, the Iwata Studio Series compressors are much quieter than diaphragm compressors or industrial compressors. Click here to view our piston compressors.
Oil-less Compressors - Piston compressors (above) can be either of the oil-filled or oil-less type. Oil-filled compressors are usually more silent as they benefit from the lubrication of the oil, but oil-less compressors like the Iwata Studio Series are still very quiet running compared to diaphragm compressors and industrial compressors. The main advantage of oil-less compressors is that you do not have to remember to check or change any oil, making them low maintenance, and there is no risk of spilling oil when your compressor is in transit if you are mobile. Click here to view our oil-less compressors.
Industrial compressors - If you wish to run a small spray gun with a larger nozzle or at higher pressures then you will need a bigger industrial compressor. The disadvantage of an industrial compressor is that it is noisier - that's because it has to work harder to compress more air. Click here to view our industrial compressors.
BSP (British Standard Pipe) fitting - The standard pipe fittings used internationally on many airbrush brands and most compressors. Some aibrush brands have a proprietary sized fitting and thread type on their airbrush air valves, and occasionally use the same fitting on their own-brand compressors. However, nearly all compressors have BSP fittings on their air outlets. Most medium to large compressors have a 1/4 BSP fitting and often smaller, more portable compressors have a 1/8 BSP fitting. There are some larger, more rarely used sizes on industrial machines such as 3/4 BSP. We stock adapters for the most common BSP sizes (1/8 and 1/4) and the main brand proprietary fittings.
The '1/4' refers to 1/4 inch, and '1/8' is 1/8 inch, which are the approximate diameters of the bore size of a pipe, and is not a measure of the thread of the connector/adapter. If you want to determine the size of BSP fitting then you can measure the external diameter of the male thread or internal diameter of the female thread, which should be:
Propellant cans - Pressurised air contained in a CFC-free aerosol can. You will also need a propellant can valve to connect a can to your air hose. The can valve crudely regulates the air flow. Propellant cans are a short-term solution for getting started. They do not offer a great deal of control over the air pressure. Once you have purchased a compressor, the air is essentially free, whereas the propellant cans need regular replacement. The high pressures supplied by a propellant are not recommended for beauty applications such as tanning and makeup. Obtaining the appropriate lower pressure using a compressor will be safer and more comfortable for the client and gives better efficiency of application.
Links to more resources: